Plumbing 101: A Guide to Bathtub Installation
Plumbing 101: A Guide to Bathtub Installation
Blog Article
Everybody may have their own individual thinking about How to Install a Bathtub Yourself.
Setting up a bath tub isn't specifically brain surgery, but it does need solid plumbing, woodworking, as well as often, tiling skills. Replacing an old bath tub with a brand-new one is additionally a reasonably challenging job. If the old tub is easily available, the job can move easily; if you need to open up a wall to eliminate the old tub and position the brand-new bathtub, the task is much harder. In either instance, the job is within a house handyman's skills, although you will certainly require an assistant to leave the old bathtub and embeded in the brand-new one. Make sure you have actually qualified on your own for the task as well as are comfortable trying it. Rather than employing a professional to take over a halfway-completed project, it is better to think about utilizing one before you begin. Possibilities are you may require a specialist plumber to make tube connections.
This write-up will assist you mount a brand-new tub in your restroom if you have currently purchased a new tub and do not require to transform the plan of your previous water supply pipes.
Your tools and product checklist must make up the following:
Getting ready for the Setup
Firstly, the sustaining framework provided with the bath should be fitted (if required) according to the producer's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is very important to see to it that if the tap features a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the faucets device to stop pressure on the bathtub.
Fit the flexible faucet connectors to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet via the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Ensure you make use of all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to currently prepare to be suited its last placement.
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, then the first thing you must do is separate the water system. After doing so, turn on the faucets to drain any water continuing to be in the system. The process of getting rid of the existing taps can be quite problematic as a result of the restricted access that is typically the case.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the faucets. Have a cloth ready for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipes have been removed, utilize the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the single taps from transforming during this procedure. When the faucets have been removed, the holes in the bath/basin will have to be cleansed of any old securing compound.
Prior to carrying on to fit the new faucets, contrast the pipeline links on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Mounting the Tub
Using the two wood boards under its feet, place the bath tub in the needed placement. The wooden boards are helpful in equally spreading out the weight of the tub over the location of the boards instead of focusing all the weight onto 4 small factors.
The following objective is to guarantee that the tub is leveled all round. This can be accomplished by checking the level as well as readjusting the feet on the tub up until the level checks out level.
To mount taps, fit the bottom of the furthest flexible faucet port to the proper supply pipe by making a compression join; then do the very same for the various other tap.
Switch on the water and also inspect all joints and also new pipework for leaks and tighten them if essential. Fill up the bath tub and additionally inspect the overflow electrical outlet and also the normal outlet for leakages.
Finally, take care of the bathroom paneling as defined in the maker's instruction manual. Tiling and sealing around the bath tub ought to wait up until the bathtub has been used a minimum of when as this will certainly settle it right into its last setting.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, then you will need decreasing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin ensuring that the washing machines are in location in between the tap and the sink. Protect the tap in position with the manufacturer supplied backnut. When the faucet is safely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical tap ports. The former type must be connected to the tap finishes first, tightening up just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the location where the bathroom fulfills the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to fracture a rigid seal, triggering the water to permeate the wall between the bath and also the tiling, leading to problems with moisture and also possible leaks to the ceiling below.
You can select from a variety of coloured sealers to blend in your components and also fittings. They are marketed in tubes and cartridges, as well as can securing voids as much as a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of drenched newspaper or soft rope. Keep in mind to always fill the bath tub with water prior to securing, to allow for the activity experienced when the bathtub remains in usage. The sealer can split rather early if you do not think about this activity prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise quickly offered on the marketplace. It is a good idea to fit the tiles utilizing waterproof or waterproof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a fervent reader on How to Install a Bathtub Yourself, I figured sharing that short article was worth the trouble. So long as you liked our page if you please remember to pass it around. I thank you for reading our article about Tools You Need to Install a New Bathtub .
Professional touch for plumbing woes. Report this page